Ruger Performance Parts

 

November 9, 2010 1:46 PM

 

Description
Product #
Qty Price

Barrel Bedding Block

When bedding rimfire rifles from the barrel, use this block as a recoil lug and stock bolt retainer. Also serves as an extra forend recoil lug and attachment point for falling block, rolling block and other single shot centerfire rifles.

Technical Information

Notes: Intended to improve bedding, needed for 10/22 actions with threaded barrel where the barrel lug has been removed. Use as recoil lug in forend area for other type actions. May require alteration to rifle for use. Steel 1.03" x .5" x .475" with .437" radius. Includes block, escutcheon, 10 32 x 1" machine screw, 10 32 x 1" cap screw, two 6 48 x 3/8" cap screws.

918534

Barrel Bedding Block

In Stock $12.99

Gunsmither Safety Takedown Tool Ruger 10-22, 10-22 Magnum

Takedown tools make disassembly simple and easy, helping avoid damage to firearm or user. Steel with Rubber Handle.

414743

Gunsmither Safety Takedown Tool

In Stock $12.99

Receiver Drilling Fixture Ruger 10/22

This drilling jig permits cleaning a 10/22 from the rear without removing the barrel. It locates the correct spot on the rear of the receiver for a hole to be drilled that allows the cleaning rod to pass through. Helps keep the rifle accurate by eliminating damage done by the cleaning rod when inserted through the muzzle.

Technical Information

Notes: 4" long, steel Locates cleaning hole location in receiver. Permits cleaning from the rear without barrel removal. Requires that a hole be drilled in the rear of the receiver. Instructions: Remove the two bolts and fiber washers from the fixture. The 10/22 receiver must be completely disassembled with all parts removed, however the barrel can stay in the receiver. The fixture mounts to the right side of the receiver. Use some suitable material to protect the receiver, then place it on the fixture, lining up the threaded holes in the fixture with the trigger guard retaining pin holes. Use the bolts with the fiber washers to hold the receiver on the fixture. Put the receiver with the fixture in a padded vise, orient it so that the rear of the receiver is facing up. Use a .257" diameter drill bit (this is an "F" drill bit) to drill a hole in the rear of the receiver. Use the bushing in the fixture as a drilling guide. Use Tap Magic to lubricate the bit while drilling. Do not drill more than 1" into the receiver. Deburr the hole with a small file or other tool. This hole will allow a cleaning rod to access the bore from the rear of the receiver. The cleaning hole may be threaded with a 5/16" 18 tap and plugged if desired. Reassemble the 10/22 and check for proper functioning before use (which should be done anytime a firearm is disassembled).

912648

Receiver Drilling Fixture Ruger 10/22

In Stock $38.99

Ruger 77 and 77 Mark 2 Pillar Bedding Columns

Columns have been precisely machined with the proper angles for a simple bedding job on the Ruger 77. Aluminum.

Technical Information

Notes: Aluminum, front .600" long, .535" diameter. Rear 1.145" long, .535" diameter. Front pillar is cut to match the receiver screw angle, fits against the bottom of the recoil lug.

874663

Ruger 77 & 77 Mark 2 Pillar Bedding Columns

In Stock $12.19
Ruger Receiver Oversize Tap (Tialn Coated)   In Stock $187.00
Ruger Receiver Standard Tap (Tin Coated)
In Stock $187.00

Trigger Adjustment Pins Ruger Mark 1 & 2

Pins mount to the outside of the firearm, allowing the trigger to be installed on the exterior of the frame. This allows the engagement surfaces to be observed in preparation for stoning. Steel.

Technical Information

Notes: Steel construction Used for adjusting the sear and trigger pull.

970862

Trigger Adjustment Pins Ruger Mark 1 and 2

In Stock $28.99

Mainspring Pusher Ruger Mark 1,2

Pusher provides complete control when removing and replacing the latch pin. Technical Information

Notes: Steel, 1 1/4" thick, 3 1/4" long Punch controls compression, block holds mainspring housing so latch pin is removed or installed.

844380

Mainspring Pusher Ruger Mark 1,2

In Stock $58.99

Trigger Adjustment Pins Ruger Single Action Revolver

Pins mount to the outside of the firearm, allowing the trigger to be installed on the exterior of the frame. This allows the engagement surfaces to be observed in preparation for stoning. Steel.

Technical Information

Notes: Steel construction Used for adjusting the sear and trigger pull.

731060

Trigger Adjustment Pins Ruger Single Action Revolver

In Stock $28.99

Yoke and Crane Alignment Tool Ruger Six Series

This tool detects any misalignment due to a bent yoke on both Ruger and S&W revolvers. Allows adjustment for more consistent crane lock up and smoother operation.

Technical Information

Notes: This tool allows precision crane alignment Tool is 3.025" long, fits Ruger Security Six, Speed Six, Service Six, knurled end may need to be shortened to fit 2 1/2" barrel.

386768

Yoke and Crane Alignment Tool Ruger Six Series

In Stock $28.99

 

 

 


 


<-Back to top

© Copyright 2008 -- Pacific Tool and Gauge Inc.
PO BOX 2549 - 598 Ave C * White City, Oregon 97503 * 1-541-826-5808 FAX: 541-826-5304